36 Talas 29 160mm FIT4 Factory - 2016
Move your mouse over image or click to enlarge

Fox Racing Shox

Fox Racing Shox 36 Talas 29 160mm FIT4 Factory - 2016

Out of stock


2206 grams

This item may only be shipped within the United States.


Welcome to the all-new 2016 Fox 36
In 2015, Fox gave their 36-series suspension forks a number of improvements that trickled down from the RAD (Racing Application Development) program. These improvements included a chassis that was not only stiffer, but a half pound lighter than the previous chassis.

3-Position FIT4 Damper
The all new FIT4 damper is somewhat similar to the Fox's previous CTD system, but it has been reworked in several ways. Fox has ditched the Climb/Trail/Descend nomenclature, and opted for Open/Medium/Firm which correlate to the three main compression settings offered on forks using the FIT4 damper. In the open position, the fork's oil flow is maximized, providing a very plush and responsive feel overall. The medium position stiffens the initial compression, allowing the fork to ride slightly higher in it's travel, reducing pedal bob/feedback. The firm setting will be increase initial compression resistance even more, and will offer the firmest ride of the three settings. Naturally, the open setting is intended for downhill trail sections, the medium setting is intended for primarily flat trail sections, and the firm setting is intended for climbing. In the open mode, the FIT4 damper offers 22 clicks of low speed compression, though it does lack the externally adjustable high speed compression that the RC2 damper offers. Why offer such a range of compression adjustment in the open setting when you could just flip the knob to the medium setting? Good question. The medium setting is intended for a quick on-the-fly switch to a firmer platform. On the inside of the fork, the medium setting, the fork has to push through a shim stack ever time it is compressed, which results in slightly harsher small bump performance. The open setting however does not utilize that shim stack, resulting in unadulterated performance - so it makes sense to give those extra 22 clicks of compression adjustability in this setting, as that is where you'll likely be spending the most time when riding.

The FIT4 damper also includes some other notable changes and improvements over the previous CTD damper. Fox's CTD system was met with a fair bit of criticism from riders and media, and folks primarily complained that the CTD forks were overdamped, somewhat unresponsive, and wallowed in their travel too much in the Descend/Open setting. Meanwhile all the forks using the RC2 damper were generally very well received, and didn't suffer from these issues. So it comes as no surprise that the new FIT4 damper borrows much of it's technology from the RC2 damper. The FIT4 utilizes a 10mm shaft and seal head design that increases oil flow to the base valve, same as what's used on Fox's 36 and 40-series forks. Fox also increased flow through the rebound circuit for faster recovery from hard hits. With the increased oil flow throughout the entire damper, as well as improvements to inner seal heads, the new FIT4 forks will be very plush and responsive in the open setting.

Talas Adjustable Travel
The Talas feature provides two-step adjustable travel between 110 and 140mm. Simply turn the crown-mounted Talas dial to the short travel setting, and push down on the fork. This setting is ideal for climbing when you need to keep the front end lower. Flip the lever back to the long travel setting, and you're ready for action.

Other Details
Fox employs a convertible axle system on the 36 RC2 series forks, allowing you to utilize either 15mm or 20mm bolt-on axles. Both axles are included. This gives you ultimate flexibility in front hub/wheel options. The 36 forks with the FIT4 damper employ a 15mm QR axle, non-convertible. Since the 36-series Fox forks are targeted towards the more aggressive crowd, they opt for a 180mm post mount disc brake tab, meaning the smallest rotor you can with this fork is 180mm. Magnesium lowers, aluminum top crown, and an aluminum steer tapered steer tube keep weight down. As with all Factory Series Fox forks, the 36 Float utilizes Fox's famous Kashima buttery smooth coating on the stanchions. All 36 29" forks have a 51mm crown offset, which is recommended for most 29" bikes on the market. This fork is backed by Fox's limited 1-year warranty.


  • Travel: 120-150mm Adjustable
  • Wheel Size: 29"
  • Spring: Air
  • Disc Mount: 180mm Post Mount
  • Travel Adjust: Yes
  • Axle Config.: 15x100mm or 20x110mm
  • Max Rotor Size: 203mm
  • Crown Material: Aluminum
  • Lowers Material: Magnesium
  • Stanchions: 36mm Aluminum
  • Steertube Dia.: Tapered
  • Crown Offset: 51mm
  • Warranty: Limited 1 Year
  • View/Download Fox 36 tuning guide

Recently Viewed Products